1 EN Instruction Manual TechniSat TechniNet Base Unit & IP IRD-Cards DVB-S2 DVB-C DVB-T www.technisat.de www.technisat.com
10 EN 4 Programming The configuration of the card is possible in three different ways: 1. Programmer (art. No. 0000/5971) connected via cable 2.
11 EN 4.1 Programmer 4.1.1 Menu structure 0000/5972 IP:10.10.110.101 Main Menu Inputs -> Inputs Statu
12 EN Main Menu Outputs -> Constellation 256 Inputs QAM -> Frequency 442000KHz Freque
13 EN Outputs Status -> Status Decoder OK-> Outputs CI -> CI Source TUNER
14 EN Stream IP Addr 10.10.70.43 Output Ethernet -> Stream Netmask 255.255.255.0 Stream Gateway 10.10.7
15 EN Uni/Multicast Setup -> 0-Uni/Multicast ID 238.1.1.1 0-Uni/Multicast Port 1234 0-Destina
16 EN Trap IP Addr 10.10.70.66 System Trap IP Addr -> Unit Name DVB-S2 0000/5972 System Unit Name -
17 EN 4.2 Connection of the programmer Remote Control For the local operation of the modules, the cable connected TechniNet IP Programmer will be
18 EN 4.3 Main Menu, System 4.3.1 LAN Interface Please configure your network settings of the LAN interface before you start working with TechniN
19 EN 4.3.2 Trap-IP Configure the destination IP Address for the distribution of Trapps to the TMS. You are within the main menu, Section: System.
2 EN Content 1 Safety advice...
20 EN 4.3.4 Firmware version Information on the firmware version can be requested here. You are within the main menu, Section: System..
21 EN 4.3.5 Factory settings Reset the module parameter back to the factory settings: You are within the main menu, Section: System. F
22 EN 4.3.7 HTTP Login Login Data for using the web-interface can be configured here: (see chapter 4.6). You are within the main menu, Section: Sy
23 EN 4.4 Main Menu, Inputs 4.4.1 DVB-S2 reception In the following you can find the information for setting the reception parameters for the sa
24 EN Please choose the auxiliary voltage multi switches auxiliary voltage for the multi switch: 13V = Vertical Low-Band 18V = Horizontal Low-Ban
25 EN 4.4.2 DVB-C reception In the following you can find the information for setting the reception parameters for the cable reception: The menu
26 EN 4.4.3 DVB-T reception In the following you can find the information for setting the reception parameters for the terrestrial reception: The
27 EN 4.4.4 Multicast-reception The menu for the configuration for the Multicast reception is only available when the TS/IP interface as input is
28 EN Setting of the Multicast-Address Setting of UDP Port Selection of the transmission protocol: UDP = User Datagram Protocol RTP = Re
29 EN 4.4.5 Monitoring of the RSSI Data Here you can monitor the reception parameter: You are within the main menu, Section: Inputs.
3 EN 4.6.3.2 ASI2/SDI Output ...
30 EN 4.5 Main Menu, Outputs 4.5.1 TS/IP Interface configured The menu to configure the TS/IP interface is only available in case of TS/IP inter
31 EN Request of the MAC Address of the TS/IP Interface Input of the MAC Address of the Gateways for the network, to which the TS/IP interface
32 EN Max Throughput = Maximising of Through put Min Delay = Minimizing of deferment Selection of data source TUNER = Tuner ASI Input = ASI input
33 EN 4.5.1.1 Uni-/Multicast play out The data transmission can be Unicast or Multicast. Unicast In case of unicast-transmission the data will be
34 EN Set the transmission parameter for a channel. Chose a channel In case of Multicast-transmission we suggest using the following rang
35 EN Selection of the service transmitted EIT play out TDT/TOT play out 0-Program T-EinsExtra ENTER ENTER 0-EIT P
36 EN 4.5.1.1.2 DVB Mode (MPTS) In the DVB mode the complete transponder will be played-out via an address. (details see 2.1.2). For this the foll
37 EN 4.6 Web-Interface For programming the card via the web-interface, please open the web browser and insert the IP-address of the corresponding
38 EN Output Status Description Video Audio Input Status ASI Description Total BitRate Input data rate, brutto. Valid Bitrate Input data rate, ne
39 EN 4.6.2 Input Depending on the type of card, the tuner is available for different transmission standards. 4.6.2.1 DVB-S2 In the section Inpu
4 EN 1 Safety advice For your own safety you should read this first and carefully – please pay attention to the given advice before you start oper
40 EN Save the value with a click to the Apply button. 4.6.2.2 DVB-C In the section Input you can the configure parameter of the DVB-C-Tuner. Pi
41 EN 4.6.2.3 DVB-T In the section Input you can the configure parameter of the DVB-T-Tuner. Picture: 6 COFDM Setting Description value Terr Fr
42 EN ASI Output Description value Source Selection of data source ASI, Tuner, CI Descramble Packet Size(Byte) Selection of Bytes per TS-Packet (M
43 EN SDI Output Description value Audio DID Selection of audio group 1, 2, 3 or 4. Group 1 to Group 4 Emb Audios Group 1 designates audio channel
44 EN 4.6.3.4 Decoder Config In the section Decoder Config you are able to configure parameter of the program to decode. Picture: 10
45 EN Biss Info Description value Biss Mode Activation of the biss descrambling systems off, 1, E Video Output Description value Video Standard V
46 EN 4.6.4 CI Within the Section CI you can choose the programs to encrypt (CAM needed).With a CAM and the appropriate Smartcard, depending on th
47 EN 4.6.5 IP In/Out In the section IP In/Out you can configure the TS/IP Interface. Picture: 12 IP Output Description value Source Selection
48 EN IP Output Description value Type of Service TOS is used for priorizing IP – data packages Normal, MIN DELAY, MAX THROUPUT, MAX RELIABILITY,
49 EN 4.6.5.1.1 DVB Mode (MPTS) Choosing this configuration, the card plays out the full received DVB-data stream via the TS/IP interface (TSoIP).
5 EN > The device may only be kept in rooms (away from radiated heat or heat sources), where, even if the climatic conditions change, the permis
50 EN Picture: 14 IP Mode Setting description Channel Number Selection of the IP TV channel 1-6 or 1-32. Multi-/Unicast IP Multi-/Unicast IP Ad
51 EN 4.6.6 System In the section System you can configure System Information.
52 EN Picture: 15 Device Info This window offers general information on the card. 1. Unit Name: you can dedicate a name to the card. Save the v
53 EN No Exist = TS/IP is switched off Filter Function Machine Type Save the value with a click to the Apply button. Login Change the Login Da
54 EN 5 Technical Data 5.1 Input Tuner DVB-S / EN 300 421 Frequency range 950…2.150 MHz Input level 42...82 dBµV Tuner input F jack Impedance 75
55 EN Channel bandwidth 6, 7, 8 MHz FFT mode 2k, 8k Guard interval ∆/Tu 1/4, 1/8, 1/16, 1/32 FEC 1/2, 2/3, 3/4, 5/6, 7/8 ASI / EN 500 83-9 Interfa
56 EN Cable based D-Sub 15 high density 5.4 General Power consumption Nonimal temperature range 0…45°C
57 EN Your device is CE approved and meets all necessary EU standards. Subject to changes and printing errors. Status 2/11 Reproduction and copies
6 EN 2 General 2.1 Description The TechniNet IP IRD cards receive a large number of channels of the DVB-S/S2, DVB-C or DVB-T signal and transmit
7 EN 2.2 Description of the operating elements Front view Element Description LAN RJ-45 socket, network connection, full-duplex TS/IP RJ-45 soc
8 EN 3 Bringing into service ESD-safety During operation of the device the ESD-safeguards in accordance with DIN EN 100 015-1 have to be observed
9 EN 3.2.3 Handset The 15pol. D-Sub Connector should be used for the connection of the programmer unit (0000/5971) via cable. 3.2.4 TUNER IN Aft
Commentaires sur ces manuels