TechniSat HD S2X Manuel d'utilisateur

DiSEqC1.2IntegratedVideo RecorderPP VV RRFor receiving free-to-air and encrypted (e.g. VIACCESS, CONAX, IRDETO, SECA etc.) HD satellite Programmes.Wit

Safety notesFor your own protection, please read through the safety precautions carefully beforeproceeding to operate your new unit.The manufacturer w

In the following cases you should disconnect the receiver from the mains power, andshould consult an expert:> the mains cable or the mains plug are

4 Connecting the DVB receivera. Mains connectionb. Connection between the LNB 1 and the LNB input 1 of the DVB receiver. (Pleasenote: when operating t

The references a b c etc. mentioned below relate to the illustration on page 12.4.1 Mains power connectionThe digital receiver should only be connecte

4.4 Video cassette recorder (VCR)f Connect the video recorder to the SCART socket VCR. During playback, the videorecorder will provide a switching sig

5 Initial installationAfter you have read the safety notes and connected the unit as described in Chapter 4,switch the unit on as described in Chapter

> Use the green function key Accept to confirm and accept the selection, and to goto the antenna configurationAntenna configurationThis step of the

All the satellites included in your antenna configuration will be scanned forProgrammes. This procedure may take a few minutes. Please note any messag

6 SettingsNow that you have connected your new digital receiver, and commenced operating it, youcan, if you wish, proceed to optimise its functions fo

6.2.3 Date/hourIn this menu point decide whether the hour and the date should be automatically read infrom a determined programme after switching on.&

1 Contents1 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Illustrations . . . . . .

> Now, using the up/down arrow keys, mark the line Picture Settings.> Confirm by pressing OK.The Menu Picture settings will appear.> Use the

> Confirm by pressing OK.The Menu Picture settings will appear6.4.1 Audio speech> In this line, use the arrow keys left/right to select your pre

prematurely terminated, the satellite positions ASTRA and EUTELSAT will be pre-programmed. If you also wish to receive other satellites, or if you are

- Record a programme and at the same time another programme from the samereception field (1 programme in HD format and 1 programme in SD format or25 p

System examples6.5.5 Additional settings/LNB propertiesOnce you have completed adjusting the switching matrix of your DVB receiver to therequirements

Polarisation> Use the up/down arrow keys to enter the desired polarisation plane (horizontal orvertical).Symbol rateThe symbol rate indicates the v

If the function is switched on you can configure four lists of favourites (main list,favourites 1, favourites 2 and favourites 3). The ex-works progra

> Press the red function key Back.A corresponding query then appears.> If you wish to accept the changes, use the arrow keys left/right to click

7 Operation7.1 Switching on and off> Switch the digital receiver on by pressing the On/Standby either on the receiver oron the remote control.>

> Press the OK key.The active programme list will be displayed.> Now, with the assistance of the option key you can open a window with the types

6.6.7 Network settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .267 Operation . . .

> Insert a CI module in one of the slots.> Insert the Smartcard in the card slot of the CI module. Ensure that the gold-colouredchip of the Smar

7.4 Volume controlYou have the facility to adjust the volume of your digital receiver. This facilitates the easyoperation of the receiver, as it means

> Use theTV/Radio key to switch the digital receiver to radio mode.The receiver will now switch to the last radio programme previously selected.>

7.12 Videotext7.12.1 Using the Videotext decoder of your television setIf transmitted, the Videotext is forwarded to your television set. To operate t

7.13 SubtitlesWhere subtitles are broadcast, this will be indicated by the message Subtitle select. Ifyou have switched on the function Subtitles (as

- to simultaneously reproduce two programmes (1 programme in HD format and 1programme in SD format or 2 programmes in SD format) even if these are rec

The EPGplus functions allow you to:- display information on programme contents on the screen- display preview pictures of individual programmes- mark

> Use the left/right arrow keys to move through the programme list one page ata time. The EPGplus functions (Point 7.16.7) are now available.> P

corresponding programme. If there is a picture available, it is indicated by .> Use the arrow keys or the function keys to mark the desired progra

programme automatically from the EPGplus data. Both the starting and the ending time ofthe programme will be taken over correct to the nearest minute.

8.1.2.5 How to programme new event timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .468.1.3 Timeshift function . . . . .

If you are interested in specific types of programmes, you can have the programmeinformation displayed by various genres, e.g. movies, news, etc.>

8 Hard drive operationYour PVR receiver (PVR=Personal Video Recorder) is equipped with an integrated harddisk drive. There is no provision for this dr

- Simultaneously record 2 programmes from the same reception band(1 programme in HD format and 1 programme in SD format or 2 programmes inSD format) a

> Use the arrow keys up/down to mark the line with the desired action.> Confirm by pressing OK.The receiver will record the whole programme and

8.1.2.1 Manual programming of timer> Use the Menu key to call up the Main menu.> Use the arrow keys up/down to mark the line Manage timer.> C

6-7 Repeat only on weekdays> Use the arrow keys up/down to select the desired function.> Confirm and accept the setting by pressing OK.Saving da

> Press the green function key New to go to the entry window for programming a newtimer event.Now make your settings here in accordance with Point

> To go to a specific point in a currently running recording, you can use thefunctions Play, Pause as well as Fast Wind and the Jogshuttle, as desc

playback procedure by pressing OK.8.2.1.2 Pause/Freeze frame> To stop the playback of a recording (freeze frame) press the yellow function key orth

> Press the right or the left arrow key while  or  is displayed in order toskip forward or back by 10 minutes.Create Picture> Press the

322 Illustrationsblue fast forwardred rewindyellowPause,playbackgreenPVR Navigator,StopOn/StandbyProgramme list on/offBackVolume +Menu on/offSound on/

8.2.2.1 On-screen controlsYour receiver is capable of playing files in MP3 format that have been stored on the harddrive or on a storage medium attach

An MP3file will be indicated on the display with its respective name, e.g. Sterne.mp3.A folder will be indicated by a display of square brackets, e.g.

The various modes are shown on screen resp. on the display panel as follows:8.2.2.4 PlaylistTo draw up a play listYou have the possibility of drawing

A list of the MP3 files available on the hard drive or the USB device will appear.These are indicated by the symbol . Folders located on the hard dri

> Use the up/down arrow keys to mark the line Pictures and confirm with OK.> Use the arrow keys up/down to select the source from which you wish

> Use the arrow keys up/down to select the source from which you wish to viewthe picture files, and confirm by pressing OK.A list showing the pictu

green function key PLS -.To delete a playlist> While in normal operating mode, press the green function key to open the PVRnavigator.> By pressi

as a standard feature.In addition, a yellow progress bar (3) will be displayed, showing the current playbackposition and the total duration of the rec

the line rename mark.> Confirm by pressing OK, to open the virtual keyboard, in order to enter a new name.> Use the yellow function key to alter

markers.> To do this, mark the beginning and the end of the section to be removed with onemark each as described under Setting a mark.> Now use

Front of unitBack of unit42LNBinput 1LNBinput 2SCART socketTVComponents;Video und Audio-outputs analogueVideo-OutputAudio outputsdigitalAudio outputsa

> If you wish to give the recording a different, specific name, then use the arrow keysup/down to mark the line New.> If you press the OK key, t

8.3.2.1 CopyingThe Copy function will effect a copy of the marked file resp. folder to be stored on the harddrive, resp. the USB device. The original

> Use the arrow keys up/down to mark the file or folder you wish to delete.> Press the blue function key Functions to open a window showing the

> Use the arrow keys up/down to mark the line Export and confirm by pressing OK.> To copy the marked file, you must now press the yellow functio

8.3.5 Hard drive maintenance> Press the OK key to obtain an overview of the number of recordings as well as thedegree to which the hard drive is fi

9 Changing the basic programming9.1 Configuring the Favourites listThis chapter describes how you may change the pre-programming of your digital recei

> Using the up/down arrow keys select the desired programme lists (e.g.languages). > Confirm by pressing OK.An additional selection window will

> To remove several programmes simultaneously, mark these as described in Point9.1.4 (Marking blocks).> When you have completed marking the desi

9.2 Programming the electronic programme guideYour receiver gives you the option of receiving a data channel with additional EPGplus datavia ASTRA sat

> If you select the start category Genres you can then also select the preferred genre(e.g. film, news, shows, etc.) as described above.9.2.4 EPG c

719.2.4 EPG channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .699.2.5 Selecting a

message Loading EPG and an indication of the EPGplus data already downloadedin the display panel.> The downloading procedure can be interrupted by

> Now use the numeric keys to enter the current unit PIN code in the line Unit PIN(factory setting 0000).> In the line Enter new PIN use the num

1. Automatic ScanSelect this type of search to scan all the satellites set in the menu Antenna settings (Point6.4 and 10.4) for Programmes.2. Satellit

> Use the arrow keys up/down to mark the line Search mode.> By pressing the OK key, decide whether you wish to scan only for free-to-airprogramm

9.4.4 Manual searchShould a programme not be found in the course of an automatic search, a satellite search ora transponder search, it may be necessar

BackThe newly found programmes are not added to the Favourites list, and are retained only inthe Total list.> Use the arrow keys left/right to sele

9.5.3 Updating the programme list (ISIPRO)The ISIPRO programme list updating function ensures that the programme list of yourreceiver will automatical

> To update the new programme list automatically, press the green function keyAutomatic.The downloading of the programme list will be started, and

Accept all programmes> To accept and transfer all new programmes without a further check, press the yellowfunction key Automatic.The programmes wil

software for your digital receiver is available. If a new version of the operating software isavailable, this will be indicated by a message displayed

Dear customer,congratulations on your decision to purchase the DigiCorder HD S2X digital receiver.The operating manual supplied is intended to help yo

10 Use with a rotating antenna (DiSEqC 1.2)Your digital receiver is ready for use with a motorised rotating antenna. Using the DiSEqCcontrol (DiSEqC l

10.1.3 Setting the West limit> To enter the West limit, first use the arrow keys to mark the field Save.> Now press the arrow key left to rotate

Example: Co-ordinates of Daun/GermanyDeg. latitude 50° 11‘(45“) NDeg. longitude 06° 50‘ (10‘‘) EConverting the degrees latitude (DL):DL = 50 + 11/60DL

> When you have completed setting the test transponder, press the Back key to returnto the menu for setting the motorised antenna. > Use the arr

> To open the window listing the available actions, press the blue function keyActions.> Now use the arrow keys up/down to mark the line Autofoc

> By pressing the yellow function key Turn to Sat the antenna will be turned to theselected satellite position.10.5 Deleting a satellite positionTo

12 Technical dataDBS-Tuner1. SAT Front End (with DVB-S2)Input frequency range 950 ... 2150 MHzDemodulation DVB-S (QPSK); DVB-S2 ((8PSK,QPSK)Symbolrate

Audio decodingAudio compression MPEG-1 & MPEG-2 Layer I and II, MP3Audio Mode Dual (main/sub), StereoSampling frequencies 32 kHz, 44.1 kHz, 48 kHz

HDMI-outputHDCP copy protection (rev 1.1 or later)HDMI downwards-compatible to DVIMains jackEthernet 10/100baseTx Socket RJ45Auto-MDIX cable cross-ove

Remote controlRemote control system RC-5Subsystem address 8 (SAT 1), 10 (SAT 2)Modulation frequency 36 kHzInfrared wavelength 950 nmPower supplyPower

3 Please read this first> Before starting to use your receiver, please check that all the components have beensupplied correctly.The following shou

13 Troubleshooting guideProblem Possible cause Solution Various programmes not shown inthe programme listWrong programme list selected Select differe

Problem Possible cause Solution Time not shown in standby mode Time not acquired Set to major channel e.g. ZDF forapprox.30 secondsReceiver cannot be

For everyday useSwitching on and off> Switch the digital receiver on by pressing the on/standby key on either the unit itselfor on the remote contr